Common Rail - Principles

Principles

Solenoid or piezoelectric valves make possible fine electronic control over the fuel injection time and quantity, and the higher pressure that the common rail technology makes available provides better fuel atomisation. In order to lower engine noise, the engine's electronic control unit can inject a small amount of diesel just before the main injection event ("pilot" injection), thus reducing its explosiveness and vibration, as well as optimising injection timing and quantity for variations in fuel quality, cold starting and so on. Some advanced common rail fuel systems perform as many as five injections per stroke.

Common rail engines require very short (< 10 second) or no heating-up time at all, dependent on ambient temperature, and produce lower engine noise and emissions than older systems.

Diesel engines have historically used various forms of fuel injection. Two common types include the unit injection system and the distributor/inline pump systems (See diesel engine and unit injector for more information). While these older systems provided accurate fuel quantity and injection timing control, they were limited by several factors:

  • They were cam driven, and injection pressure was proportional to engine speed. This typically meant that the highest injection pressure could only be achieved at the highest engine speed and the maximum achievable injection pressure decreased as engine speed decreased. This relationship is true with all pumps, even those used on common rail systems; with the unit or distributor systems, however, the injection pressure is tied to the instantaneous pressure of a single pumping event with no accumulator, and thus the relationship is more prominent and troublesome.
  • They were limited in the number and timing of injection events that could be commanded during a single combustion event. While multiple injection events are possible with these older systems, it is much more difficult and costly to achieve.
  • For the typical distributor/inline system, the start of injection occurred at a pre-determined pressure (often referred to as: pop pressure) and ended at a pre-determined pressure. This characteristic resulted from "dummy" injectors in the cylinder head which opened and closed at pressures determined by the spring preload applied to the plunger in the injector. Once the pressure in the injector reached a pre-determined level, the plunger would lift and injection would start.

In common rail systems, a high-pressure pump stores a reservoir of fuel at high pressure — up to and above 2,000 bars (29,000 psi). The term "common rail" refers to the fact that all of the fuel injectors are supplied by a common fuel rail which is nothing more than a pressure accumulator where the fuel is stored at high pressure. This accumulator supplies multiple fuel injectors with high-pressure fuel. This simplifies the purpose of the high-pressure pump in that it only has to maintain a commanded pressure at a target (either mechanically or electronically controlled). The fuel injectors are typically ECU-controlled. When the fuel injectors are electrically activated, a hydraulic valve (consisting of a nozzle and plunger) is mechanically or hydraulically opened and fuel is sprayed into the cylinders at the desired pressure. Since the fuel pressure energy is stored remotely and the injectors are electrically actuated, the injection pressure at the start and end of injection is very near the pressure in the accumulator (rail), thus producing a square injection rate. If the accumulator, pump and plumbing are sized properly, the injection pressure and rate will be the same for each of the multiple injection events.

Read more about this topic:  Common Rail

Other articles related to "principles":

List Of Nikola Tesla Patents - American - Patents #1–#50
... of energy Simple construction Easier construction Rotating magnetic field principles ... circuit and stator Construction and organization principles ... Armature for Electric Machines - 1889 December 24 - Construction principles of the armature for electrical generators and motors Simple and economical Coils of insulated conducting wire (or ribbon) may be ...
National Medal Of Technology And Innovation - Laureates
... and research, as a Professor of Industrial Engineering and Management Science, on the principles of technology commercialization." 1990 Fred W ... his lifetime work of providing the key principles and methods by which enterprises manage the quality of their products and processes, enhancing their ability to compete in the global marketplace." 1992 Charles ... economics, general systems theory and technology, statistical methods and management principles that define the Total Quality Management approach for achieving performance excellence and ...

Famous quotes containing the word principles:

    The machines that are first invented to perform any particular movement are always the most complex, and succeeding artists generally discover that, with fewer wheels, with fewer principles of motion, than had originally been employed, the same effects may be more easily produced. The first systems, in the same manner, are always the most complex.
    Adam Smith (1723–1790)

    It is always easier to fight for one’s principles than to live up to them.
    Alfred Adler (1870–1937)

    It is the genius of our Constitution that under its shelter of enduring institutions and rooted principles there is ample room for the rich fertility of American political invention.
    Lyndon Baines Johnson (1908–1973)